A super bonding and penetrating vinyl primer

Can be applied using normal spray, airless spray, roller or brush

Suitable for application to porous surfaces and hard surfaces

Extremely flexible

A completely waterproof coating

Very fast drying time

Single pack system allows simple application and re-coating

The primer for the PV211-INTER system

The use ensures the maximum performance of the total system

Provides the short term protection of freshly blasted steel

Colour: Clear (can be tinted)

Gloss: Gloss

Solids Content: 13% v/v, 19% w/w

Thickness: 8mm DFT above blasting peaks

Theoretical Coverage: 6 square meters @ 25 um

Practical Coverage: Allow appropriate loss factors

Method of Application: Spray, Airless Spray, Roller or Brush

Drying Time: 3-10 minutes to touch

5-20 minutes at 22^oC (70F)

Over coating: Compatible systems must be applied within 7 days

Environmental Conditions: Can be applied between 7.5^oC and 60^oC

Substrate temperature must be 3^oC above dew point

Flexibility: Extremely

Elongation: 500-600%

Tensile: 2500-3500 psi

Precaution:

DANGER!! Extremely flammable prior to application. Keep away from heat and open flame. Keep out of reach of children. Do not take internally. If swallowed take one or two glasses of water or milk, induce vomiting and seek medical assistance.

Flammability: extremely

Flash Point: less than -5^oC (30F) Open Cup

Product Mass: approx. 0.89 kg/l (7.5 lbs./gal)

SURFACE PREPARATION

Because coating life is dependent primarily upon surface preparation, this aspect of the cleaning program should receive very thorough consideration. The requisite of any method of surface preparation is that the surface be thoroughly cleaned of any material or contaminants that are liable to cause premature failure of the coating.

Prior coating the substrate is to be clean, dry and free from contamination and should be assessed and treated in accordance with ISO 8504:1992.

Oil or grease should be completely removed using a suitable solvent.

Metal Preparation using Abrasive Blasting:

Remove all weld spatter. Grind sharp edges to 3mm radius and make sure all welds are smooth and solid.

Metal surfaces must be abrasive blasted to a metallic white finish. A de-rusting degree of Sa 2½ as specified in ISO 12944-4 and a "medium G" roughness degree as specified in ISO 8503-1 must be achieved; minimum roughness Rz = 50mm. On completion of blasting clean surface with clean air and ensure that all contaminants are removed.

PV211-PRIME must be applied before any flash rusting occurs and on the same day as blasting.

Any surface defects revealed by the blasting process must be repaired, re-blasted and patch primed.

APPLICATION

Mixing: No mixing of different packs is required. The product is single pack. Agitate PV111-PRIME prior to use using a power agitator.

Pot life: No short-term pot life as single pack system

Airless Spray: Suitable - Tip Range: 516 - 517

- Total output fluid pressure at spray tip not

less than:

Air Spray: Suitable

(Pressure Pot)

Brush: Suitable

Roller: Suitable

Thinner: May be thinned with MEK to a maximum 5% MEK by volume

Cleaner: Simple detergents

Work stoppages: Do not allow material to remain in hoses, guns, spray equipment or brushes. Thoroughly flush all equipment with MEK. Unused clean material maybe returned to the original container.

Clean Up: Clean up all equipment after use with MEK. It is good practice to periodically flush out spray equipment during the course of the day. Frequency of cleaning will depend on amount sprayed, temperature, and elapsed time including any delays.

All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations / legislation.

Surface Prep: Adjust the extent of surface preparation to reflect the quality of the existing System. If the system is damaged through to the substrate then the area should be re-prepared and the complete system reinstated. Should the system be in good condition the surface should be made free of contaminates and washed with a suitable solvent prior to re-coating. PV111-PRIME maybe omitted if the surface has not needed to be blasted.

Reapplication: As per Application.

This product has been developed to perform as a system in conjunction with PV211-INTER intermediate coat and the optional PV311-TOP top coat. The use of PV111-PRIME is integral to the performance of the complete system; in some cases the use of other primers will give inferior performance.

The use of PV311-TOP is primarily used to achieve a gloss finish to the paint system and as such maybe omitted without detriment to the system performance in some cases. Refer to your local ICS Distributor for advice.

This product is designed to be only applied by those applicators trained by Industrial Coating Solutions in conditions and to the specifications in this data sheet and in the Materials Safety Data Sheet (MSDS) supplied with the product. Additional copies of the MSDS are available through your local distributor.

All work done using this product should be performed in compliance to all regional Health, Safety and Environmental regulations / legislation.

As a minimum, basic safety for personal protection should be:

Long sleeve overalls or disposable overalls,

Rubber gloves,

Splash shield or safety glasses with splash guards,

Protective breathing apparatus,

Rubber or leather boots,

Apply in a well ventilated area,

Do not apply near high heat or open flames,

Do not take internally,

Keep out of reach of children.

If you have any queries regarding the safe use of this product consult you local distributor.

W ARRANTY, DISCLAIMER &

Industrial Coating Solutions reserves the right to replace or refund the cost of product that has been found to be defective when applied according to this data sheet by trained applicators.

This data sheet is not designed to be exhaustive. If in doubt additional information can be found through you local product distributor. Do not use this product if there is any doubt regarding its proper use or application. Industrial Coating Solutions have endeavoured to ensure the information provided herein is accurate. In view of the multitude of possible operating conditions and object parameters, no express or implied warranties of any kind are made and no claims based on this data will be allowed.

This data sheet is liable to be changed from time to time in line with constant improvements to the product. Industrial Coating Solutions reserve the right to change the data sheet without prior notice and prior publications will become invalid on release of the revised data sheet.