PRODUCT DESCRIPTION

A high performance, flexible, chemical resistant, anti-corrosive coating

Can be applied using normal spray or airless spray

High anti-corrosive properties against common industrial acids and alkalis

Fully stabilised and pigmented suitable for continuous exterior exposure

No chalking (UV resistance)

Resistant to mechanical damage

Suitable for continuous immersion

Single pack system allows simple application and re-coating

As a anti-corrosion coating

Duties range from a general-purpose exterior coating to protection for steel against attack by aggressive chemicals depending on the thickness of application

As a watertight coating in continuous immersion applications

As a vessel lining

As a protective coating on walkways and structural steelwork

As a coating for steel, aluminium, exterior panels and wood

GENERAL INFORMATION

Colour: As per Australian Standard

Gloss: Gloss

Solids Content: 15.5% v/v, 25% w/w

Thickness: As required to meet duty (See Systems Data Sheet)

Theoretical Coverage: 6 square meters @ 25 um

Practical Coverage: Allow appropriate loss factors

Method of Application: Spray or Airless Spray

Drying Time: 20 minutes to touch

72 hours at 22^oC (70F)

Environmental Conditions: Can be applied between 7.5^oC and 60^oC

Substrate temperature must be 3^oC above dew point

Flexibility: 180 bend over 1/8" at 0 ^oC (32F)

Elongation: 200%

Bridging Ability: 12.5 mm

Tensile: 1800 psi

MVT: 0.32 perms @ 15 mils

Precaution:

DANGER!! Flammable prior to application. Keep away from heat and open flame. Keep out of reach of children. Do not take internally. If swallowed take one or two glasses of water or milk, induce vomiting and seek medical assistance.

Flammability: Will not support combustion

Flash Point: -6^oC (21F) Open Cup

Product Mass: approx. 1.08 kg/l (9 lbs/gal)

SURFACE PREPARATION

Oil or grease should be completely removed using a suitable solvent.

The first coat of PV211-INTER should always be applied over PV111-PRIME. The primer surface should be dry and free from all contamination and PV211-INTER must be applied within the over-coating intervals specified for PV111-PRIME (Consult the relevant data sheet)

Areas of breakdown, damage etc. should be prepared to the specified standard and patch primed prior to the application of PV211-INTER.

Mixing: No mixing of different packs is required. The product is single pack. Agitate PV211-INTER prior to use using a power agitator.

Pot life: No short-term pot life as single pack system

Airless Spray: Suitable - Tip Range: 516 - 517

- Total output fluid pressure at spray tip not

less than:

Air Spray: Suitable

(Pressure Pot)

Brush: Suitable for touch up only

Roller: Not suitable

Thinner: Do not thin

Cleaner: Simple detergents

Work stoppages: Do not allow material to remain in hoses, guns, spray equipment or brushes. Thoroughly flush all equipment with MEK. Unused clean material maybe returned to the original container.

Clean Up: Clean up all equipment after use with MEK. It is good practice to periodically flush out spray equipment during the course of the day. Frequency of cleaning will depend on amount sprayed, temperature, and elapsed time including any delays.

All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations / legislation.

Surface Prep: Adjust the extent of surface preparation to reflect the quality of the existing System. If the system is damaged through to the substrate then the area should be re-prepared and the complete system reinstated. Should the system be in good condition the surface should be made free of contaminates and washed with a suitable solvent prior to re-coating. PV111-PRIME maybe omitted if the surface has not needed to be blasted.

This product has been developed to perform as a system in conjunction with PV111-PRIME primer. The use of PV111-PRIME is integral to the performance of the complete system; in some cases the use of other primers will give inferior performance.

This product has been developed to perform as a system in conjunction with PV311-TOP topcoat. The use of PV311-TOP is primarily used to achieve a high sheen, abrasion resistant finish to the paint system and as such depending on the application the use of PV311-TOP maybe omitted without detriment to the system performance. Refer to your local distributor for advice.

SAFETY PRECAUTIONS

This product is designed to be only applied by those applicators trained by Industrial Coating Solutions in conditions and to the specifications in this data sheet and in the Materials Safety Data Sheet (MSDS) supplied with the product. Additional copies of the MSDS are available through your local distributor.

All work done using this product should be performed in compliance to all regional Health, Safety and Environmental regulations / legislation.

As a minimum, basic safety for personal protection should be:

• Long sleeve overalls or disposable overalls,
• Rubber gloves,
• Splash shield or safety glasses with splash guards,
• Protective breathing apparatus,
• Rubber or leather boots,
• Apply in a well ventilated area,
• Do not apply near high heat or open flames,
• Do not take internally,
• Keep out of reach of children.

If you have any queries regarding the safe use of this product consult you local distributor.

WARRANTY, DISCLAIMER & ADDITIONAL INFORMATION

Industrial Coating Solutions reserves the right to replace or refund the cost of product that has been found to be defective when applied according to this data sheet by trained applicators.

This data sheet is not designed to be exhaustive. If in doubt additional information can be found through you local product distributor. Do not use this product if there is any doubt regarding its proper use or application. Industrial Coating Solutions have endeavoured to ensure the information provided herein is accurate. In view of the multitude of possible operating conditions and object parameters, no express or implied warranties of any kind are made and no claims based on this data will be allowed.

This data sheet is liable to be changed from time to time in line with constant improvements to the product. Industrial Coating Solutions reserve the right to change the data sheet without prior notice and prior publications will become invalid on release of the revised data sheet.